Aztech ADSL2+ Ethernet Router User's Guide Page 11
- Page / 36
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Figure 4 (Bridge Connection Setup)
To complete the connection you must now click the apply button. The apply button will
temporarily save this connection. To make the change permanent, you need to click on Save
Settings. At the system commands page, click on Save All.
4.4.1.2 PPPoA Connection Setup
PPPoA is also known as RFC 2364. It is a method of encapsulating PPP packets over ATM cells
which are carried over the DSL line. PPP or Point-to-Point protocol is a method of establishing a
network connection / session between network hosts. It usually provides a mechanism of
authenticating users. LLC and VC are two different methods of encapsulating the PPP packet.
Contact your ISP to make sure which encapsulation is being supported.
By selecting PPPoA, you are forcing your ADSL Router to terminate the PPPoA connection. The
advantage is that the PPPoA termination is done within the ADSL Router and not on your PC; this
frees up your PC resources and allows multiple users to utilize the PPPoA connection.
To configure the gateway for PPPoA, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select PPPoA and the PPPoA
connection setup page is displayed; figure 5 illustrates a typical PPPoA configuration. Give your
PPPoA connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called PPPoA1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
service provider or your ISP will supply these; in this case the DSL service provider is using
0,100. Also select the quality of service (QOS); leave the default value if you are unsure or the
ISP did not provide this information.
- 11 -
- Web Interface User’s Guide 1
- - 2 2
- 1. Introduction 3
- 1.1 Features 3
- 1. PWR/POWER 5
- 2. ETH/ACT 5
- 4. DSL 5
- 5. PPP/Internet 5
- - 6 6
- Figure 1 (Log-in screen) 7
- - 7 7
- 4.2 Quick Start 8
- - 9 9
- 4.4 Configuring the WAN 10
- - 11 11
- - 12 12
- - 13 13
- - 14 14
- - 15 15
- - 16 16
- 4.4.3 Modem setup 17
- 4.5 Configuring the LAN 18
- - 19 19
- - 20 20
- 4.5.3 Firewall/NAT Services 21
- 4.6.1 UPnP 22
- 4.6.2 Port Forwarding 23
- 4.6.3 Advanced Security 24
- 4.6.4 Access Control 25
- 4.6.5 LAN clients 25
- 4.6.6 MAC Address Filters 26
- 4.6.7 Multicast 27
- 4.6.8 Static Routing 28
- 4.6.9 Dynamic Routing 29
- 4.7 Tools 30
- 4.7.4 Ping Test 31
- 4.8 Status 32
- 4.8.3 DHCP Clients 33
- 4.8.4 Modem Status 33
- 4.8.5 Product Information 33
- 4.8.6 System Log 33
- - 34 34
- - 35 35
- 6. ADSL Router terms 36
Related products and manuals for Networking Aztech ADSL2+ Ethernet Router
Networking Aztech DSL500U User Manual
(27 pages)
(27 pages)
Networking Aztech ADSL USB Modem User Manual
(26 pages)
(26 pages)
Networking Aztech Easy User Manual
(46 pages)
(46 pages)
Networking Aztech WL559E User Manual
(45 pages)
(45 pages)
Networking Aztech 56K PCI Modem User Manual
(47 pages)
(47 pages)
Networking Aztech DSL9100R User Manual
(32 pages)
(32 pages)
Graco Dyna-Star 5:1 manuales
Manuales del propietario y guías del usuario para Equipo Graco Dyna-Star 5:1.
Ofrecemos 1 manuales en pdf Graco Dyna-Star 5:1 para descargar gratis por tipos de documentos: Manual de usuario
Comments to this Manuals